1. Home
  2. Support
  3. H1F Vacuum Only Pump – Discontinued
H1F
  1. Home
  2. Support
  3. H1F Vacuum Only Pump – Discontinued

H1F Vacuum Only Pump – Discontinued

Discontinued – H1F Vacuum Only Pump – 36 CFM. Replacement parts are available. Check out the upgraded H1 Series vacuum pump. See below for more details!

  • Airflow

    36 CFM

  • Port Size

    1″

  • Series

    H1 Series
View product Find replacement parts

Pump Manual

Download Manual

Print Resources

H1F Brochure
Download file
Blog Header Image

Support Videos

Learn how to rebuild your vacuum pump, change your pump’s vanes, and much more!
Available in English and Spanish

Visit Blog

Technical Specifications

H1F

  • Airflow

    36 CFM

  • Port Size

    1″

  • Oiling System

    Plastic Reservoir with Adjustable Drippers

  • Weight (approx.)

    55 lbs

  • Oil Reservoir Options

    Plastic Reservoir with Drippers

  • Optimal Tank Size

    75 to 500 Gallons

  • Max Vacuum (Continuous)

    20″ Hg

  • Max Vacuum (Intermittent)

    27″ Hg

  • Max Pressure (Continuous)

    15 P.S.I.G.

Dimensions

  • Length

    10.46875″

  • Width

    7.34375″

  • Height

    11.3125″

Replacement Parts

H1 Series Rebuild Kit

Rebuild Kit- H1 SERIES

$363.24
ADD
H1 Series Vane Pack

Vane Pack – H1 SERIES

$203.41
ADD
H1 Series Gasket Seal O Ring

Gasket, Seal, O-Ring kit – H1 SERIES

$49.90
ADD
Oil Line 10 Foot

Oil Line – 10 Ft

$35.49
ADD
Oil Line - 50-Foot

Oil Line – 50 Ft

$184.77
ADD
Shaft Guard

H1F, HXL2, & HXL3 Shaft Guard

$42.25
ADD

FAQ

RPM FAQ

Yes, all products have a 1-Year Limited Warranty.

To keep the pump in a workable condition, operators should undertake regular maintenance and keep a written log of those checks.

Before Starting

  • Ensure a vacuum relief valve and a pressure relief valve are installed in the system and adjusted to recommended settings, taking into account the altitude of the job location.
  • Always bleed the tank to atmospheric pressure before switching the valve from vacuum to pressure or from pressure to vacuum.

Every Load

  • Drain the scrubber after each tank load. If nothing drains when the ball valve is opened, never assume it is empty, check for a blockage in the valve.
  • Check the oil level in the oil reservoir and fill as required.
  • Monitor vacuum/pressure and temperature gauges to detect any irregularities or problems.

Daily

  • Add oil approximately every 10 hours of operation, or when the oil reservoir shows the level is low. Only use approved lubricants.
  • Drain the oil separator twice daily. A brass ball valve is mounted at the bottom for easy draining.

Weekly

  • Flush the pump weekly with Masport Flushing Fluid, or any time that liquids or solids have been allowed to enter the pump.
  • Check and clean the Inlet Filter. Ensure the filter is completely dry before refitting. This checking process must be done any time contamination may have entered the system.
  • Check to ensure the pump RPM is within the recommended range. Running the pump too fast or too slow may cause damage.
  • Wash any dirt off the pump, as it needs to be clean to allow heat to radiate and prevent it from overheating.

Annually

  • Check bolt mountings, drive coupling alignment and condition, and vane wear.

Storage

  • If the pump is to be sitting for an extended period of time, it needs to be flushed prior to storage. After flushing, pour oil into all bearing lubrication ports to protect the bearing surfaces and oil injection points on the pump to eliminate rust formation on the rotor and cylinder.
  • Rotate by hand monthly to distribute oil.

Yes! In order to operate efficiently and at their best, vacuum pumps rely on heat radiating to keep them cool. If mud or debris becomes packed on and around the vacuum pump, the heat has trouble escaping and the performance becomes limited.

Masport vacuum pumps require little regular maintenance except for flushing the pump. This should be done weekly or anytime liquid or solids have been allowed to enter the pump. Flushing Fluid specifically formulated for Masport pumps is available from your local Masport representative or by contacting Masport.

1 Gallon Bottles | Part # 13990
4 Gallon Case | Part # 13991
12 Gallon Case | Part # 13992

Rotary Vane Vacuum Pumps require a high quality non-detergent Rotary Compressor Oil or Rotary Turbine Oil. Oil specifically formulated for Masport pumps is available from your local Masport representative or by contacting Masport Inc.

1 Gallon Bottles – All Seasons Blend
Part # 13980

4 Gallon Case – All Seasons Blend
Part # 13983

12 Gallon Case – All Seasons Blend
Part # 13984

Warning!

 Do NOT use transmission fluid, automotive motor oil, power steering fluid, used oil, vegetable oil, brake fluid, hydraulic fluid, gear oil or scented oil in a Masport pump.

Substitutes

See below for a list of approved oil alternatives.

Get Help

Have a quick question or need assistance troubleshooting on your pump? Our Help & Support resources are great for independent pumpers on the go.

Find Resources

Contact Sales

We’re not that kind of sales team. Get in touch and tell us what you’re looking for. We’ll give you options and get you back to work quickly with the best products on the market.

Schedule a Call

Contact Support

Not finding what you need?  Reach out to our Customer Support team for quick, effective solutions and get you back to your day.

Contact Support

Stay in
the know!

To receive updates on our products and services, join our Masport newsletter.

Cart Have a coupon ?
Products you might like
Subtotal $1,003.94
Shipping
Calculate shipping
Sales Tax Taxes will be calculated at checkout
Total $1,003.94
Checkout - $1,003.94
  • 2
  • 3